RV Electric Leveling Repair - Daytona Beach, FL
RV Repair Daytona Beach troubleshoots and repairs electric leveling systems - including Lippert Ground Control TT, Equalizer, and Atwood electric tongue jacks - that fail to extend, retract, or hold level. We test motor brushes, gear assemblies, control boards, and wiring harnesses on-site. Most electric leveling faults are resolved in under 2 hours without a shop visit.
How Lippert Ground Control and Power Gear Electric Jacks Work

Electric leveling systems replace the hydraulic pump and cylinder circuit with a DC motor at each jack location. Lippert Ground Control 3.0 - one of the most common systems on current-production fifth wheels and Class A gas coaches - uses a 12-volt motor driving an acme-thread screw that extends and retracts a steel foot. Power Gear electric jacks use a similar drive mechanism with a slightly different control interface.
The advantage of electric systems over hydraulic is the elimination of fluid leaks and fewer shared failure points - one failed jack motor does not affect the others. The disadvantage is that each jack must be serviced individually, and a failed motor requires physical access to the jack mount. Our technicians carry replacement motors, limit switch assemblies, and control module firmware update cables for Lippert Ground Control 3.0 and the earlier 2.0 platform, covering the majority of fifth-wheel and Class A electric leveling installations from 2015 onward.
Diagnosing Electric Leveling Control Module Faults

The Lippert Ground Control 3.0 control module is the brain of the electric leveling system - it reads the inclinometer, sends commands to each jack motor relay, and monitors current draw on each motor circuit. When the module detects a fault, it generates a blink code on the panel LED and, on units connected to Lippert's OneControl network, logs the fault with a timestamp. We retrieve the fault log using a Bluetooth diagnostic tool, which lets us see whether the fault is recurring or one-time, and whether it correlates with a specific jack position or a temperature event.
Common module-level faults include a failed inclinometer that gives false level readings, a relay that sticks open and prevents one jack from receiving power, and a firmware bug in early 3.0 units that causes premature cycle termination. Firmware updates for Ground Control 3.0 are applied via USB cable - we carry the current firmware file and update the module on-site when a known fix addresses the observed fault.
RV Leveling System Repair Cost in Daytona Beach, FL
| Service | Typical Cost | Notes |
|---|---|---|
| Service Call + First Hour | $299 - $399 | Travel + diagnostics anywhere in Volusia County |
| Leveling Solenoid Replacement | $200 - $450 | Lippert, HWH, or Power Gear; common failure |
| Hydraulic Pump Motor Replacement | $400 - $900 | Includes fluid flush; HWH or Power Gear |
| Jack Cylinder Seal Replacement | $250 - $600 | Per jack; HWH or Lippert hydraulic |
| Auto-Level Control Board Replacement | $350 - $800 | Lippert or HWH controller; programmed on-site |
| Electric Jack Motor Replacement | $200 - $450 | Lippert electric slide-out or stabilizer jack |
Pricing note: Ranges shown are average costs for the Daytona Beach, FL market based on common repair scenarios. The exact cost of your repair depends on your RV make and model, the severity of the issue, and parts availability.
Only a technician on-site can provide an accurate estimate after inspecting your RV. A written estimate is provided before any work begins - you approve it before we start.
RV Electric Leveling Repair - Common Questions
My electric leveling jacks hum but won't move - is that the motor or the gearbox?
A hum with no movement almost always means the motor is energized but mechanically blocked - the most common causes are a seized gear assembly, a stripped drive gear, or a jack leg that is physically bound from road debris or corrosion. RV Repair Daytona Beach removes the jack assembly, inspects the gear train, and replaces only the failed component.
How long do the motors in Lippert Ground Control electric jacks typically last?
Lippert Ground Control jack motors typically last 8 to 12 years under normal use, though corrosion from road salt and moisture ingestion can cut that lifespan in half in northern climates. Brushed DC motors wear predictably - if you notice slower jack movement or increased current draw, that is an early warning sign our technicians can confirm during a service call.
Can I manually retract electric leveling jacks if the motor fails while I'm trying to leave a campsite?
Yes - most Lippert and Equalizer electric jacks have a manual override hex socket on the gearbox that accepts a cordless drill or hand crank, letting you retract the jacks without motor power. The override location and socket size are in your owner's manual - RV Repair Daytona Beach can also walk you through it by phone and then meet you to repair the failed motor.
Can I manually crank my Lippert Ground Control jacks if the motor fails?
Yes - Lippert Ground Control jacks have a hex socket at the top of the drive shaft that accepts a 3/4-inch breaker bar. You can manually extend or retract each corner independently using this socket.
It is slow but effective for getting the rig level while waiting for a motor replacement. We include the socket location and procedure in our arrival call if you need to level before we get there.
How long do Lippert Ground Control electric jack motors last?
Under normal use - seasonal camping with routine maintenance including annual drive screw lubrication - Lippert Ground Control motors typically last eight to twelve years. Jacks that are operated on unlevel ground requiring long extension travel wear faster. Keeping the drive screw clean and lubricated with a dry PTFE lubricant is the single highest-impact maintenance item for motor longevity.